1JZ / 2JZ Racing Parts, KAZAMA

KAZAMA T3 Turbocharger Blanket

Titanium heat-shield blanket for T3 turbochargers. Insulates the hottest area of the engine bay to...

KAZAMA T4 Turbocharger Blanket

Titanium heat-shield blanket for T4 turbochargers. Insulates the hottest area of the engine bay to...

KAZAMA FA20/FA24 to 1JZ-GTE/2JZ-GTE Conversion Engine Bracket – Toyota 86 ZN6 / GR86 ZN8

Engine brackets for converting the 86 ZN6 (FA20) or ZN8 to a 1JZ-GTE or 2JZ-GTE...

KAZAMA 2JZ A/C Dummy Pulley Bracket (with VR Pulley) – Toyota 2JZ

A/C dummy (delete) pulley bracket for the 2JZ, refined with data from Kazama's own 2JZ-GTE...

KAZAMA SR20 Stainless Oil Pan Baffle Plate Set – Nissan SR20

Stainless-steel oil pan baffle plate set for the SR20. On used or long-stored SR engines...

KAZAMA R154 Transmission Mount Bracket – Nissan Silvia S14 / S15

Swapping a 2JZ into an S14 / S15 normally needs one-off fabrication. This bracket mounts...

KAZAMA Direct Ignition Coil Base Plate (Set for One Engine) – Toyota 1JZ / 2JZ Non-VVT-i

Base plates that sit between the engine and the direct ignition coils on 1JZ /...

KAZAMA 1/2JZ-GTE Engine Mount Bracket – Nissan Silvia S14 / S15

Engine mount brackets for swapping a Toyota JZ engine (1JZ / 2JZ-GTE with VVT-i) into...

KAZAMA Nissan Drive Shaft Spacer 2pcs (for BNR32 / BCNR33 Drive Shafts)

Spacers that fit between the differential and drive shaft when the shaft ends up too...

KAZAMA LINK Plug-in ECU Case (#NS15X) – Nissan Silvia S15

3D-printed replacement for the factory ECU case. A LINK Plug-in ECU needs the original Nissan...

KAZAMA Quick Change Drive Shaft Conversion Adapter 45mm (for JZX100 Drive Shafts)

Adapter that converts a Quick Change / Bulldog differential flange to accept Toyota factory JZX100...

KAZAMA Quick Change Drive Shaft Conversion Adapter 20mm (for JZX100 Drive Shafts)

Adapter that converts a Quick Change / Bulldog differential flange to accept Toyota factory JZX100...

KAZAMA Quick Change Drive Shaft Conversion Adapter (for Nissan BNR32 / BCNR33 Drive Shafts)

Adapter that converts a Quick Change / Bulldog differential flange to accept Nissan factory BNR32...

KAZAMA Quick Change Drive Shaft Conversion Adapter 25mm (for JZX100 Drive Shafts)

Adapter that converts a Quick Change / Bulldog differential flange to accept Toyota factory JZX100...

KAZAMA Rear Hub 114.3 Conversion Adapter for JZX100 Drive Shafts – Toyota 86 ZN6 / GR86 ZN8

Adapter kit that converts the rear hubs on the ZN6 / ZN8 factory knuckles to...

KAZAMA Quick Change Mounting Bracket

Mounting bracket for installing a quick change rear end, made by Kazama for its own...

KAZAMA Quick Change Repair Bearing (Small 6207)

Spare 6207 bearing for quick change / Bulldog rear ends — the smaller bearing on...

KAZAMA Quick Change Repair Bearing (Large 6307)

Spare 6307 bearing for quick change / Bulldog rear ends — the bearing you see...

KAZAMA SPICER Tube Yoke (3-28-57)

SPICER tube yoke (part 3-28-57) as used by Kazama on its own competition / demo...

KAZAMA Clutch Clevis (Long / Short) – Toyota JZX Series

Clutch clevis for the Toyota JZX series that lets you adjust the clutch engagement point...

KAZAMA SPICER Universal Joint Kit (5-178X)

SPICER Drivetrain Products universal joint kit (part 5-178X) as used by Kazama on its own...

KAZAMA Caliper Mounting Bracket (JZX81 → S14 Caliper) – Toyota Mark II / Chaser / Cresta JZX81

Bracket set that lets you bolt factory Nissan 4-pot front calipers (S14 / S15 /...

KAZAMA Rigid Diff Mount Weld Plate – Toyota JZX Series

Weld-in plate that replaces the rubber in the factory JZX differential mount bushes with solid...